Working with ASME BPVC VIII-2 chapter 5: “Design by Analysis”
Regular fee € 750
Instructor-led Live Sessions
Starts May 28, 2020
4 Live Sessions
Daniel van Baalen, MSc
Learn from home
100% online training
Lectures by Industry Experts
connect with them online
to recordings and material
Receive Personal Certificate
and prove your knowledge
Dynaflow Research Group currently applies a 50% discount to all its online courses to service its
customers during these challenging times,
Regular fee: € 750,-
Current fee: € 375,-
About the course
4 Live sessions
Starts May 28
The ASME Boiler & Pressure Vessel section VIII code is the most frequently used pressure vessel design code in the world. Two design approaches are present in the code: design by rules and design by analysis. Design by Analysis in ASME VIII-2 Part 5 is used to complement the Design by Rules parts of the code. Why might this be necessary? Perhaps a feature is located too close to a discontinuity or has a non-standard configuration, perhaps a detailed fatigue calculation is required or loadings other than pressure are present?
This course covers how to conduct Design by Analysis code compliance checks for rupture, ratcheting, fatigue and buckling load cases.
During which topics such as the difference between primary or secondary stresses, the influence of weld type on fatigue life and obtaining the structural stress will be addressed using FEM software.
Questions? Contact us
+31 (0)85 058 0051
Monday - Friday, 9am - 6pm CEST
Meet your instructor
Program & Details
Welcome to the course
How to use this course
Personal Certificate requirements
Introduction to “Design by Analysis” as per the ASME BPVC VIII division 2.
Failure mode A: plastic collapse
Compliance checks for plastic collapse
Examples of assessments
Linearization of your stress results
Exercise provided after the session:
Manually performing linearization
Discussion of exercise: Manually performing linearization
Failure mode B: ratcheting
Compliance checks for ratcheting
Examples of ratcheting assessments
Failure mode C: fatigue
Fatigue assessment methods
Examples of fatigue assessments
Failure mode D: buckling & local failure
Compliance checks for buckling
Example buckling assessment
Course evaluation survey
Your Personal Certificate
Rate this course
Related resources & follow up
After this course, you...
understand the General Definitions and Failure Mechanisms associated with ASME VIII-2 Ch. 5 (Design by Analysis) assessments,
have a good overview of the code section,
can perform Stress Categorization and are able to link results to failure mechanisms,
have seen numerous practical examples with Shell and Brick Finite Element Models,
know the concepts of Stress Linearization and are able to apply them,
understand Fatigue Analysis using both Welded and Smooth Bar Methods
Who should attend this course
Those using Finite Element Analysis for pressure vessel design,
People involved in projects for which the ASME VIII-Div. 2 Design by Analysis is used,
People that need to read technical reports related to this topic,
Beginner and intermediate pressure vessel designers.
Prerequisites: Basic understanding of Finite Element Analysis
This course consists of 4 instructor-led live sessions which consists of presentations, demonstrations and discussions of questions. During each session, participants can ask questions to the instructor (through chat or microphone) which will be answered. After each live session the recording of that session, used slides and exercise documents are made available to participants to view again. If desired by the instructor, exercise files are provided at the end of a session that will be discussed in the next session. These should be performed by the participant before they are discussed in the upcoming live session.
Access to the course
After your purchase is confirmed you receive an account to the EngineeringTrainer online learning portal, where you find the course welcome chapter and instructions on how to join the live sessions. Sessions are held using the software GoToMeeting and a log-in link is provided for each session through the portal. A test link is provided from the start such as to test if you are able to properly join the sessions prior to the first session. Live sessions can be joined using any device, including tabled and mobile.
You receive 6-months unlimited access to the course. This allows you to watch content again if this is beneficial for your work projects.
The live sessions are scheduled twofold to service participants in different time-zones. Upon enrollment each participant is appointed to a group based on their preferences.
Group A (Asia, Middle East, Europe, Africa, Australia) - Registration Closed
Session 1: May 28, 9am CEST (1hr) (convert time-zones)
Session 2: June 4, 9am CEST (1hr)
Session 3: June 11, 9am CEST (1hr)
Session 4: June 18, 9am CEST (1hr)
Group B (North & South America, Europe, Africa)
Session 1: June 8, 4pm CEST (1hr) (convert time-zone)
Session 2: June 16, 4pm CEST (1hr)
Session 3: June 22, 4pm CEST (1hr)
Session 4: June 30, 4pm CEST (1hr)
After the course you receive 6-months unlimited access to all course material including recordings of the live sessions. This allows you to watch recording of lectures again whenever you need to refresh knowledge for your daily work projects.
A personal digital certificate will be made available to each participant upon full attendance. If you are unable to attend any of the sessions please notify us as we will require to view the recordings.
This course consists of 4 instructor-led live sessions which consists of presentations, demonstrations and discussions of questions. During each session participants can ask questions to the instructor (through chat or microphone) which will be answered.
After each live session the recording of that session, used slides and exercise documents are made available to participants to view again. If desired by the instructor, exercise files are provided at the end of a session that will be discussed in the next session. These should be performed by the participant before they are discussed in the upcoming live session.
Exercise files can be downloaded, these can include .pdf files with the exercise questions, software models or other file types. Videos will not be available for download, but can be accessed directly with your account on the portal. If slides are used in the videos or live sessions these can be viewed separately as well through the portal, but are not available for download. You receive 6-months unlimited access to the course. This allows you to watch content again if this is beneficial for your work projects.
Yes, interactive Q&A sessions are included in this course that allow you to interact with the instructor and ask questions.
No software is required for participants of this course.
Demonstrations are provided using the FEM software FEPipe, but having access to this software is not required.